Simple T Track for Woodwork Jigs





Introduction: Simple T Track for Woodwork Jigs

I started to make a new small cross cut sled for my table saw the other day and decided to make the t slot directly in the fence rather than buying an aluminium one,
with that in mind I decided to write this little article to show people just how easy they are to make. this method can be used to make slots in jigs or to make a track to install in a jig.


  • A piece of wood suitable for making the fence or track ( hardwood is best )
  • 1 nut and bolt sized for the application ( for my example I have used 8 mm )


  • A table saw or Router (optional used as an alternative for cutting the slots)
  • Good quality wood glue
  • Clamps


Firstly we need a suitable piece of wood for the project I would suggest using a hardwood for this as it will last longer, an 8 mm bolt mine is around 40 mm long and a 8 mm nut,

I have then used the table saw to remove around 20 mm from the top of the piece of wood as seen in the picture below.


First we need to set the depth on the blade this needs to be just a little deeper than the head of the bolt.


With the depth set move the fence so the blade is more or less center of the wood, it does not have to be perfect just close.

Run the wood through the saw and at the end of the cut turn the wood around so the opposite face is against the fence and run through the saw again, this method will center the groove on the work piece.
With the first cut complete adjust your fence so you make the slot a little wider and once more run the wood through the saw, as before flip your work piece at the end of the first cut and run through again, repeat this process until the slot is just a fraction wider than the head of the bolt. ( Remember because we are cutting twice for each fence adjustment it will double the amount removed so be careful towards the end of the process).

With the first part cut we now turn our attention to the smaller section we removed at the start,
This time we need to set the depth on the saw to around 4 – 5 mm and once again set the fence so the work piece is roughly center on the blade. As before we do two passes through the saw for each adjustment until the slot is slightly wider than the threads on the bolt.


We now have both of the slots cut so we now need to join the top to the bottom using a good quality wood glue, spread the glue sparingly as we don’t want any excess in the slot.

(Spread the glue on the smaller faces of the bottom piece rather than the top).

Remember to wipe off the excess glue with a damp cloth and leave to dry for several hours.


After allowing the glue to dry remove the piece from the clamps and head back to the table saw.

This time we need to set the fence so the blade just cuts through the top most part of the slot as in the picture

Run the timber through the saw and you should be left with a T slot


We are going to need something to tighten the jigs, this could be just using the nut and a washer or you could make something like this out of a little bit of scrap.


  • Hi making this is wh...-PhilH40

    PhilH40 made it!


  • First Time Author Contest 2018

    First Time Author Contest 2018
  • Sew Warm Contest 2018

    Sew Warm Contest 2018
  • Paper Contest 2018

    Paper Contest 2018

We have a be nice policy.
Please be positive and constructive.




This is great. I'd often scratched my head on this one!
Just a thought that might make it easier by reducing machining…
As it stands there's a wide groove for the bolt head in the lower piece, and a narrow groove for the shaft in the upper piece.
How about machining the wide groove and the narrow groove both in the top piece?
Also sand to a fine finish and lots of silicone spray!
Well done that man.

This is a good job. I was thinking of something along this line and then saw a router bit sold on ebay that was designed to make this track in a board. One pass and its done. But there is a lot less satisfaction with a one pass solution!

Sure would like to find a one shot router jig. Best I can find is two bits. The first makes the initial cut to depth needed. Second bit does the T part by following the initial cut thus keeping the cut clean and not straining the router.

Someone makes a bit that cuts the slot in one pass, but it's not as clean as the 2 pass. It can be tough on the router also.

Nice work PhilH40 and nice name also!! I like the way you made your T track. I have thought of a couple of other ways that may work as well although I have yet to try them.

One way I thought of was to cut or route a channel slightly larger than the bolt shank you are going to use. Next using a key hole router bit route the area the head of the bolt will ride in. I think this would work well with brass toilet bolts.

The second idea was to, as before start off by cutting the channel first that is large enough for the shank and head of the bolt this time. Then use a piloted rabbiting bit to route down either side of the channel that you could then inlay thin aluminum strips leaving enough space for the bolt shank to pass between the strips. Not sure either of these would work any better than your idea though!

Nice work keep it up!

- Phil

Great nut. How did you craft that?

They are as simple as the slot is I will do a quick how to at the weekend while I am dong the next part to this one

Much appreciated. It's a neat way to add a little more class to any typical...nut job.

Sorry. I had to go there.

Why wouldn't you just glue two small pieces of wood to the top on track
instead of wasting the time and material routing out, gluing up, and
then cutting off the bigger piece you used?,,,,,,,,,,